Projectors : Projectors : Panasonic - PT-DX100U

10000 Lumens XGA 1-chip DLP Fixed Installation Projector

Model: PT-DX100U

1-Chip DLP, 10000 lumens, XGA
Excellent image quality thanks to the dynamic RGB booster and vivid colour control
Dual lamp system with lamp relay mode enables 24/7 operation
Eco filter enables up to 12000 hours of air filter replacement cycle
10,000:1 contrast ratio

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Documents

The PT-DX100U 1-Chip DLP Fixed Installation Projector delivering stunning colors and highly flexible projection for museums, exhibitions and digital signage applications.

1-Chip DLP, 10000 lumens, XGA
Excellent image quality thanks to the dynamic RGB booster and vivid colour control
Dual lamp system with lamp relay mode enables 24/7 operation
Eco filter enables up to 12000 hours of air filter replacement cycle
10,000:1 contrast ratio

Aspect Ratio - 4:3
Number of Imagers - 1-chip
Projector Applications - Digital Cinema
Projector Technology Type - DLP
Supported Resolution - XGA (1024x768)

Operating Temperature (Maximum): 45 C
Operating Temperature (Minimum): 0 C
Lamp Life Full: 12000 hours
Brightness Full: 10000 lumens
Chip Quantity: 1
Communication Formats: RS232C
Communication Ports: RS232
Contrast Ratio: 10000
Lamp Quantity: 2
Lamp Type: 420W UHM
Technology: 1-Chip DLP
AC Voltage (Maximum): 240 Volts
AC Voltage (Minimum): 120 Volts
Current Draw: 5.20 Amps
Depth: 556 mm
Height: 200 mm
Width: 498 mm
Product Weight: 18.30 kg
Regulatory Compliance: HDCP
DLP™ chip Panel size: 17.8 mm (0.7 in) diagonal (4:3 aspect ratio)
DLP™ chip Display method: DLP™ chip x 1, DLP™ system
Screen Size: 1.27-15.24 m (50-600 inches), 1.27-5.08 m (50-200 inches) with the ET-DLE055 (4:3 aspect ratio), 2.54-8.89 m (100-350 inches) with the ET-DLE030 (4:3 aspect ratio)
Center-to-corner uniformity: 90%
Resolution: 1,024 x 768 pixels (Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.)
Scanning Frequency (HDMI/DVI-D): fH: 15 - 100kHz, fV: 24 - 120Hz, dot clock: 25 - 162 MHz
Scanning frequency (RGB): fH: 15 - 100kHz, fV: 24 - 120Hz, dot clock: 162 MHz or lower
Scanning Frequency YPBPR (YCBCR): 525i(480i): fH 15.75kHz, fV 60Hz, 625i(576i): fH 15.63kHz, fV 50Hz,525p(480p): fH 31.50kHz, fV 60Hz, 625p(576p): fH 31.25kHz, fV 50Hz, 750(720)/60p: fH 45.00kHz, fV 60Hz, 750(720)/50p: fH 37.50kHz, fV 50Hz, 1125(1035)/60i: fH 33.75kHz, fV 60Hz, 1125(1080)/60i: fH 33.75kHz, fV 60Hz, 1125(1080)/50i: fH 28.13kHz, fV 50Hz, 1125(1080)/25p: fH 28.13kHz, fV 25Hz, 1125(1080)/24p: fH 27.00kHz, fV 24Hz, 1125(1080)/24sF: fH 27.00kHz, fV 48Hz, 1125(1080)/30p: fH 33.75kHz, fV 30Hz, 1125(1080)/60p: fH 67.50kHz, fV 60Hz, 1125(1080)/50p: fH 56.25kHz, fV 50Hz
Scanning Frequency (Video/S-Video): fH: 15.75kHz, fV: 60Hz [NTSC/NTSC4.43/PALM/PAL60], fH: 15.63kHz, fV: 50Hz [PAL/PAL-N/SECAM]
Optical Axis Shift: Vertical: +50% (powered) (+/-45° with the ET-DLE085/ET-DLE105), Horizontal: +/-10% (powered), NOTE: Optical axis shift function cannot be operated when used with the ET-DLE055. If using the ET-DLE030, the optical axis is fixed.
Keystone Correction Range: Vertical +/-40°, +/-30° with the ET-DLE055/ET-DLE085/ET-DLE105. Cannot be used when the ET-DLE030 is installed.
Installation: Ceiling/floor, front/rear
Terminals HDMI IN: HDMI 19-pin x 1, Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p, VGA(640 x 480) - WUXGA(1,920 x 1,200), dot clock: 25 MHz - 162 MHz, NOTE: Compatible with non-interlaced signals only.
Terminals DVI-D IN: DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single link only, 525i (480i), 625i (576i), 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/25p, 1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/30p, 1125 (1080)/60p, 1125 (1080)/50p, VGA(640 x 480) - WUXGA(1,920 x 1,200), dot clock: 25 MHz - 162 MHz, NOTE: Compatible with non-interlaced signals only.
Terminals RGB 1 IN: BNC x 5
Terminals RGB 1 IN R, G, B: R: 0.7Vp-p, 75 ohms, G: 0.7Vp-p (G: 1.0Vp-p for sync on G), 75 ohms, B: 0.7Vp-p, 75 ohms, HD, VD/SYNC: TTL, high impedance, positive/negative automatic, NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Terminals RGB 1 IN Y, PB, PR (Y, CB, CR): Y: 1.0Vp-p (including sync signal), PB/PR (CB/CR): 0.7Vp-p, 75 ohms
Terminals RGB 1 IN S-Video signal: Y: 1.0Vp-p, C: 0.286Vp-p, 75 ohms
Terminals RGB 2 IN: D-sub HD 15-pin (female) x 1
Terminals RGB 2 IN R, G, B: R: 0.7Vp-p, 75 ohms, G: 0.7Vp-p (G: 1.0Vp-p for sync on G), 75 ohms, B: 0.7Vp-p, 75 ohms, HD, VD/SYNC: TTL, high impedance, positive/negative automatic, NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Terminals RGB 2 IN Y, PB, PR (Y, CB, CR): Y: 1.0Vp-p (including sync signal), PB/PR (CB/CR): 0.7Vp-p, 75 ohms
Terminals 3D SYNC 1 IN/OUT: BNC x 1, 1.0Vp-p, 75 ohms, Input: TTL, high impedance. Output: TTL, max. 10 mA
Terminals 3D SYNC 2 OUT: BNC x 1, 1.0Vp-p, 75 ohms, TTL, max. 10 mA
Terminals VIDEO IN: BNC x 1, 1.0Vp-p, 75 ohms
Terminals SERIAL IN: D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
Terminals SERIAL OUT: D-sub 9-pin (male) x 1 for link control (RS-232C compliant)
Terminals Remoter 1 In: M3 jack x 1 for wired remote control
Terminals Remoter 1 Out: M3 jack x 1 for link control
Terminals Remoter 2 In: D-sub 9-pin (female) x 1 for external control (parallel)
Terminals LAN/DIGITAL LINK: RJ-45 x 1 for network and DIGITAL LINK (video/network/serial control) connection, 100Base-TX, compatible with Art-Net, compliant with PJLink™ (class 1), Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p, VGA(640 x 480) - WUXGA(1,920 x 1,200), dot clock: 25 MHz - 162 MHz, NOTE: Compatible with non-interlaced signals only.
Power Cord Length: 3m (9ft 10in)
Cabinet materials: Molded plastic
Operation noise: 40dB (dual lamp operation, lamp mode: normal), 35dB (dual lamp operation, lamp mode: Eco)
Operating Humidity: 10% - 80% (no condensation)

Projector 226921 kb - Other

Project List

Projector 3482515 kb - Other

Project List

Find a Dealer

Find a Distributor

Suggested Products

Pro L1750UNL WUXGA 3LCD Laser Projector without Lens, 4K Enhancement

by Epson Australia

4,200 ANSI lms1080p Short Throw Laser Installation Projector

by ViewSonic Corp.

DWU760A-iS 1DLP Laser Projector (TAA)

by Christie