Pro AV Catalog
Manufacturers
PRODUCT CATEGORIES
Matching Keywords
Model Numbers
Request Quote
All Products
Multi-channel Power Amplifier, 80W/Channel Output Power
Series: XM
Model: XM4080
- Ideal for theatre, hall, and conference room installations
- Four independent channels of power amplification in convenient, manageable units (XM4180 180W/channel, XM4080 80W/channel)
- Stereo, parallel or bridged operation switchable from the rear panel
- Balanced XLR and Euroblock connectors for easy, secure input connection
- Output connections via five-way binding posts
Product Info
Tech Specs
Documents
XM4180 and XM4080 are suitable for wide range of installed systems. Three operational modes can be selected as required the stereo mode provides four independent channels of amplification, the parallel mode allows two mono sources to drive dual amplifiers each and in the bridged mode two channels operate as single high-power mono amp, effectively giving two higher powered mono amps in one unit. The operating mode can be easily switched from rear panel. Two types of input jacks are provided, balanced XLR types and Euroblock jacks for easy, secure input connection. Output connections are made via five-way binding posts. A high pass filter with a selectable 20 or 55Hz roll-off frequency is also provided. Precision attenuators and independent indicators are provided for each channel, allowing accurate level setup and status monitoring. XM4180 is also capable of functioning as distribution power amp that can drive multiple high-impedance speakers via 70V line output. The rear panel provides a monitor/remote jack that allows the amp to be monitored and controlled from an external device.
- Ideal for theatre, hall, and conference room installations
- Four independent channels of power amplification in convenient, manageable units (XM4180 180W/channel, XM4080 80W/channel)
- Stereo, parallel or bridged operation switchable from the rear panel
- Balanced XLR and Euroblock connectors for easy, secure input connection
- Output connections via five-way binding posts
- High-pass filter with a selectable 20 or 55Hz roll-off frequency
- Precision attenuators and independent indicators for each channel allow accurate level setup and status monitoring
- XM4180 can also function as distribution power amp to drive multiple high-impedance speakers via 70V line output
- Rear-panel monitor/remote jack allows amp to be monitored and controlled from an external device
- Amplifier Signal Type - Audio
- Amplifier Type - Power Amplifier
- Spec Sheet available - Yes
- Cooling: variable-speed fan x 1
- Depth: 412 mm
- Frequency Response: maximum 0dB, typical 0dB, minimum -0.5dB, 20Hz to 20kHz (8 ohms, Po=1W, HPF=OFF)
- Height: 88 mm
- Power Requirements: 120V/60Hz, 230V/50Hz, 240V/50Hz
- Sensitivity: 4 dB
- Total Harmonic Distortion: less than 0.1% (20Hz to 20kHz, halfpower)
- Intermoduration Distortion: less than 0.1% (60Hz:7kHz=4:1, halfpower)
- Standby Power Consumption: 5 W
- Idle power consumption: 40 W
- Damping Factor: 100 (8 ohms, f=1kHz)
- Voltage Gain: 26 dB
- Maximum Input Voltage: +22 dBu
- Balanced Input Impedance: 20 kiloohms
- Unbalanced Input Impedance: 10 kiloohms
- Front Panel Controls: power switch (push on/push off), attenuator (31 position) x 4
- Maximum Frequency Response (Bandwidth): 20 kHz
- Maximum Frequency Response (Bandwidth): 20000 Hz
- Minimum Frequency Response (Bandwidth): 20 Hz
- Minimum Frequency Response (Bandwidth): 0.02 kHz
- Signal to Noise Ratio: 103 dB
- Total Harmonic Distortion + Noise (THD+N): 0.10 %
- Width: 480 mm
- Product Weight: 9.80 kg
Multi-channel Power Amplifier
200 kb
- Data Sheet
Request Quote
Thank you!
Someone will be in touch with you shortly.
Contact InSight Systems Group Pty Ltd
close
InSight Systems Group Pty Ltd
8/170 Rooks Road
Vermont, Victoria 3133
Australia
1300 369 451
www.insightsystems.com.au
Contact in regards to this product:
Yamaha Commercial Audio Systems, Inc.
Model: XM4080
Request more information from a dealer near you
close