Pro AV Catalog
Manufacturers
PRODUCT CATEGORIES
Matching Keywords
Model Numbers
Request Quote
All Products
IR + Infrared Modulator / Wi-Fi Server with Dante input supporting 2 channels. Includes TFP 065 power supply and WLC 004 line cord.
Model: IR M1 D
- The IR M1 shall have the dimensions of 19” (W) x 1.75” (H) x 8.2” (D) (48.3 cm x 4.5 cm x 20.8 cm).
- The IR M1 shall weigh 5.2 lb (2.4 kg).
- The IR M1 shall have a selectable carrier frequency of 2.3/2.8 or 3.3/3.8MHz.
- The IR M1 shall have two combination 3 pin XLR, 1/4” (TRS) jacks for balanced or unbalanced line level, or balanced or unbalanced microphone with selectable phantom power.
- The IR M1 shall have dual 1/4” headphone jacks on the front panel.
Product Info
Tech Specs
Related Products
Documents
Accessories
The IR Plus features a distributed infrared emitter array architecture allowing up to four emitters either stacked together for large room arrays or distributed throughout the room to accommodate wings in room design, balconies or other obscured venue locations.
The rack mounted or remotely located IR M1 Control Center comes standard with support for up to four IR emitters. Each emitter runs back to the modulator via a CAT5e cable, providing the audio and power needed to support the remote emitter. Each emitter has a coverage area of 18,000 sq. ft.
The IR Plus Control Center can also provide audio over Wi-Fi. Connect the IR M1 to a Wi-Fi multicast router or in-house network you can stream audio over Wi-Fi to the Williams AV WaveCAST app
- The IR M1 shall have the dimensions of 19” (W) x 1.75” (H) x 8.2” (D) (48.3 cm x 4.5 cm x 20.8 cm).
- The IR M1 shall weigh 5.2 lb (2.4 kg).
- The IR M1 shall have a selectable carrier frequency of 2.3/2.8 or 3.3/3.8MHz.
- The IR M1 shall have two combination 3 pin XLR, 1/4” (TRS) jacks for balanced or unbalanced line level, or balanced or unbalanced microphone with selectable phantom power.
- The IR M1 shall have dual 1/4” headphone jacks on the front panel.
- The IR M1 shall have four RJ-45 ports for emitter output, one dedicated RJ-45 port for LAN connection, and optional RJ-45 port for Dante input.
- The infrared modulator shall be Williams Sound model IR M1
- Demodulator/Modulator Signal Type - Audio
- ROHS Compliant - Yes
- Warranty - Yes
- Spec Sheet available - Yes
- Carrier Frequency 1: 3800 kHz
- Carrier Frequency 1: 3800000 Hz
- Carrier Frequency 1: 0 Ghz
- Carrier Frequency 2: 2800 kHz
- Carrier Frequency 2: 2800000 Hz
- Carrier Frequency 2: 0 Ghz
- Maximum Frequency Response (Bandwidth): 16000 Hz
- Maximum Frequency Response (Bandwidth): 16 kHz
- Minimum Frequency Response (Bandwidth): 40 Hz
- Minimum Frequency Response (Bandwidth): 0.04 kHz
- Certifications: CE, FCC, RCM, WEEE, CB Scheme, ISED, VCCI
- Signal to Noise Ratio: 67 dB
- Total Harmonic Distortion + Noise (THD+N): 2 %
- AC Voltage (Maximum): 240 Volts
- AC Voltage (Minimum): 110 Volts
- Active Power: 36 Watt
- Current Draw: 0.75 Amps
- DC Voltage: 48 Volts
- Depth: 208.28 mm
- Height: 44.45 mm
- Width: 482.60 mm
- Product Weight: 2.36 kg
- Colour: Black
- Warranty (Length/Type): 2 Years
- Rack Mount: Single Rack Unit
- Power Switch: Rocker switch with LED
- Modulation: FM Wideband, +50kHz deviation, 50uS pre-emphasis
- Carrier Frequency: Selectable, 2.3/2.8 or 3.3/3.8MHz
- Audio Processor Functions: DSP based; Compression 1:1, 1.5:1, or 2:1; High-pass and low-pass filter frequency control
- Auto Carrier Shut-Off: Adjustable timer shuts off carrier when no audio is present. Adjustable through webpage.
- Infrared Test LED: Dual IR LED for receiver testing, monitoring, and audio signal testing
- Audio Input: (2x) Combination 3-pin XLR, 1/4” (TRS) jack for balanced or unbalanced line level, or balanced or unbalanced microphone with selectable phantom power
- Dante: Optional
- Internal Test Tone: 400 Hz internal test tone selectable as audio input source for setup and diagnostics
- Remote Configuration: Available through embedded website
- Headphone Output: (2) 1/4" headphone jacks on front panel for monitoring CH A and CH B audio inputs
- Emitter Output Jack: Four RJ-45 ports for CAT5e cables; provides +48VDC Power, RS-485 communication, and Baseband signals for IR transmission
- Operating Requirements: 0-50ºC ambient temperature, non-condensing, non-corrosive atmosphere
IR E4
- IR Plus Emitter IR E4
IR ME1 D
- IR Plus Combo with Dante - Includes: (1) IR M1 D IR + Infrared Modulator / Wi-Fi Server with Dante input supporting 2 channels, (1) IR E4 IR + Infrared emitter, and (1) IDP 008 ADA wall plaque.
IR ME2
- IR Plus Flex - Includes: (1) IR M1 IR + Infrared Modulator / Wi-Fi Server, (2) IR E4 IR + Infrared emitters, (1) MLB 003 metal linking bar, and (1) IDP 008 ADA wall plaque.
IR SY11 D
- IR Plus Complete with Dante
IR SY12 D
- IR Plus Secure with Dante
MCAT-277-IR-M1.pdf
311795 kb
- Data Sheet
IRPlusFlyer_5_25_21.pdf
755961 kb
- Brochure
MAN-273_C-IR-M1.pdf
1552472 kb
- Instructions
Request Quote
Thank you!
Someone will be in touch with you shortly.
Contact InSight Systems Group Pty Ltd
close
InSight Systems Group Pty Ltd
8/170 Rooks Road
Vermont, Victoria 3133
Australia
1300 369 451
www.insightsystems.com.au
Contact in regards to this product:
Williams AV
Model: IR M1 D
Request more information from a dealer near you
close