Pro AV Catalog
Manufacturers
PRODUCT CATEGORIES
Matching Keywords
Model Numbers
Request Quote
All Products
Professional Graphic Equaliser with Long-throw 45mm Oil-damped Faders
Model: DN370
- Long-throw 45mm oil-damped faders with dust cover for increased accuracy and resolution
- All-new proportional-Q filters provide optimum control without undesirable audio artifacts
- Gain control with +6dB/-infinity range and centre detent at unity gain. Allows effective muting of channel in emergencies
- Range switch selects ±6dB or ±12dB operation for the faders, with LED indication
- Channel bypass switch with LED indication. The unit also provides automatic relay bypass in the event of power failure
Product Info
Tech Specs
Documents
Professional graphic equaliser with long-throw 45mm oil-damped faders with dust cover for increased accuracy and resolution. Sweepable high-pass filter with 20Hz to 500Hz range sets the lower frequency limit of the system. The control incorporates a push switch to select the filter in and out, with an illuminated ring for "at a glance" status indication. Invaluable for smooth rejection of unwanted subsonic and low frequencies, particularly relevant with modern, compact wedge monitors. Sweepable low-pass filter with 2kHz to 20kHz range sets the upper frequency limit of the system. The control incorporates a push switch to select the filter in and out, with an illuminated ring for at a glance status indication. Provides optimum bandwidth control for vocal monitors and IEM systems. Two sweepable notch filters per channel, with overlapping frequency ranges of 20Hz to 2kHz and 200Hz to 20kHz. These allow precise removal of problem frequencies with minimal effect on the rest of the program material, and fast control of between fader frequencies. This gives precise control of room and loudspeaker resonance/feedback nodes with minimum loss of energy even between ISO centres. The controls each incorporate a push switch to select the filter in and out, with an illuminated ring for "at a glance" status indication.
- Long-throw 45mm oil-damped faders with dust cover for increased accuracy and resolution
- All-new proportional-Q filters provide optimum control without undesirable audio artifacts
- Gain control with +6dB/-infinity range and centre detent at unity gain. Allows effective muting of channel in emergencies
- Range switch selects ±6dB or ±12dB operation for the faders, with LED indication
- Channel bypass switch with LED indication. The unit also provides automatic relay bypass in the event of power failure
- Bypass switch with status LEDs for quick comparison of applied EQ
- Power switch, fully recessed in the on position to avoid accidental operation
- Signal present LEDs show the presence of audio signals above -40dBu
- IEC mains inlet, the unit automatically adjusts for operation on all voltages from 100 to 240V AC
- KT logo for quality engineering and reliability 3-year KT warranty for peace of mind
- Equalizer Type - Graphic Equalizer
- Depth: 203.20 mm
- Depth:
205mm (8 inch)
- Dynamic Range: >114 dB (20Hz to 20kHz unweighted, ±12dB range)
- Frequency Response: 1kHz ±0.5 dBu 20Hz-20kHz
- Gain: -infinitive to +6 dB
- Height: 133.35 mm
- Height: 133mm (5.25 inch) (3U High)
- Impedance: 20,000 ohm
- Impedance: 20 k?
- Maximum Input Level: +22 dBu
- Width: 482.60 mm
- Width: 482mm (19 inch)
- Shipping Weight: 7 kg
- Minimum Load Impedance: 600 ohms
- Source Impedance: <60 ohms
- Overload Indicator: +20 dBu
- High Pass Filter Slope: 12 dB/Octave
- Low Pass Filter Slope: 12 dB/Octave
- Q: 32
- Maximum Level: +22 dBu
- Maximum Boost/Cut: ±6/12 dB
- Distortion (THD+N): <0.003% at 1kHz,+4dBu
- Notch Filter Attenuation: >17 dB
- Eq Out: ±0.5 dB
- EQ In: (flat) ±0.5 dB
- Product Weight: 5.80 kg
- Centre frequencies: To BS EN ISO 266:1997 25Hz to 20kHz, 1/3 octave tolerance ±5%
- Equalisation: 30 Bands
- Input two type: Electronically balanced (pin 2 hot)
- Outputs Two type: Electronically balanced (pin 2 hot)
Klark Teknik - Full Line Brochure.pdf
4559 kb
- Brochure
Klark Teknik - DN370 Brochure.pdf
1798 kb
- Brochure
Request Quote
Suggested Products
Thank you!
Someone will be in touch with you shortly.
Contact InSight Systems Group Pty Ltd
close
InSight Systems Group Pty Ltd
8/170 Rooks Road
Vermont, Victoria 3133
Australia
1300 369 451
www.insightsystems.com.au
Contact in regards to this product:
Klark Teknik
Model: DN370
Request more information from a dealer near you
close